the transformer is a device used to raise or lower the electric current. when viewed from the method of use, there are many types of transformers.
however, when viewed from the way it works, the transformer is only divided into two types.
that is :
transformer step-up and step-down transformer
and for its use, the transformer is divided among them:
Transformer Adaptor
assisted by diodes, transformers is useful to convert AC into DC current through the coil primary and secondary windings. Typically used for power supply circuit. transformer of this type has a roll to change the power voltage 110 volts to 220 volts. The rolls (coils) is called the primary winding. Before the change becomes a DC current, an electric voltage is passed through thousands conductor (coil) which ends at the secondary winding.
These components are widely sold in the market with the size and specific purposes. whereas its properties are as follows:
The physical form of the transformer is: a rectangular plate coated with a thin and rolls of paper closed. There are a few feet, the primary windings are three legs, while the secondary is not less than nine feet
The primary winding receives AC current PLN between 110-240 Volt
Secondary windings produce DC current after AC current in the second winding process on this. voltage issued from 4 to 12 volts
Transformer IF (intermediate frequency)
This transformer is used for the intermediate frequency of the amplifier, usually found in the receiving radio relic. are now rarely wears transformer electronic devices of this type. Ikeja how this transformer is capturing sound waves emitted by radio transmitters and then on though through other components. subsequently issued in the form of sound (sound). IF transformer has the physical form of a square, on a surface right in the middle there is a gap to rotate when correcting the sound emission from the radio transmitter.
The advantages of this IF transformer is:
Can be altered when looking for precisely targeted beam using a screwdriver;
The size is small making it easier for beginners when installing
Retains the primary and secondary windings
The output transformer (OT)
This component can also be called transformer OT. These components are widely used in amplifier circuits, radio receivers, tape recorder and a set of electronics that produce other sounds. Physical form is almost the same with the other transformer dhania different sizes. Contains the coil windings of Nikulin. The size of the inflow depends on the coil.
Part transverse reinforcing plates and paper package, it is used as a separate circuit breaker on the primary and secondary windings. At the bottom of the foot swell, there are five foot two on the output and three parts in (inflows).
Transformator
however, when viewed from the way it works, the transformer is only divided into two types.
that is :
transformer step-up and step-down transformer
and for its use, the transformer is divided among them:
Transformer Adaptor
assisted by diodes, transformers is useful to convert AC into DC current through the coil primary and secondary windings. Typically used for power supply circuit. transformer of this type has a roll to change the power voltage 110 volts to 220 volts. The rolls (coils) is called the primary winding. Before the change becomes a DC current, an electric voltage is passed through thousands conductor (coil) which ends at the secondary winding.
These components are widely sold in the market with the size and specific purposes. whereas its properties are as follows:
The physical form of the transformer is: a rectangular plate coated with a thin and rolls of paper closed. There are a few feet, the primary windings are three legs, while the secondary is not less than nine feet
The primary winding receives AC current PLN between 110-240 Volt
Secondary windings produce DC current after AC current in the second winding process on this. voltage issued from 4 to 12 volts
Transformer IF (intermediate frequency)
This transformer is used for the intermediate frequency of the amplifier, usually found in the receiving radio relic. are now rarely wears transformer electronic devices of this type. Ikeja how this transformer is capturing sound waves emitted by radio transmitters and then on though through other components. subsequently issued in the form of sound (sound). IF transformer has the physical form of a square, on a surface right in the middle there is a gap to rotate when correcting the sound emission from the radio transmitter.
The advantages of this IF transformer is:
Can be altered when looking for precisely targeted beam using a screwdriver;
The size is small making it easier for beginners when installing
Retains the primary and secondary windings
The output transformer (OT)
This component can also be called transformer OT. These components are widely used in amplifier circuits, radio receivers, tape recorder and a set of electronics that produce other sounds. Physical form is almost the same with the other transformer dhania different sizes. Contains the coil windings of Nikulin. The size of the inflow depends on the coil.
Part transverse reinforcing plates and paper package, it is used as a separate circuit breaker on the primary and secondary windings. At the bottom of the foot swell, there are five foot two on the output and three parts in (inflows).
Tidak ada komentar:
Posting Komentar